Take Assessment - Module 4 Exam - CCNA 3 Switching Basics and Intermediate Routing (Version 3.1) Time Remaining: 1 Which of the following is a Layer 2 broadcast address? 0.0.0.0 255.255.255.255 11:11:11:11 FF:FF:FF:FF FF:FF:FF:FF:FF:FF 2 Which of the following are true regarding the addition of switches to a network? (Choose two.) They increase the number of collision domains. They decrease the number of collision domains. They increase the number of broadcast domains. They decrease the number of broadcast domains. They increase the amount of bandwidth available to users. They decrease the amount of bandwidth available to users. 3 Which attribute is used by a bridge to make forwarding decisions? source IP address source MAC address destination IP address destination MAC address Layer 4-7 protocol address 4 Which statements are true concerning the shared memory buffering used by an Ethernet switch? (Choose two.) Frames are processed through a single queue. All frames are placed in a common memory buffer. Frames are placed in a queue for the destination port. A port with a full memory buffer can cause frames for available ports to be delayed. Each switch port is statically assigned a buffer of equal size. 5 Where are switching tables stored in a Cisco LAN switch? ROM CAM Flash SIMM NRAM 6 Which switching mode changes to store-and-forward mode after it detects a given number of errors? cut-through adaptive fast-forward fragment-free adaptive cut-through 7 Why does a switch have higher throughput compared to a bridge? Switching occurs in software. Switching occurs in hardware. Switches create multiple broadcast domains. Switches segment LANs. 8 Which statements are true regarding hubs? (Choose three.) Hubs operate at Layer 1 of the OSI model. They create separate collision domains. Signals are distributed through all ports. Layer 2 addresses are used to make decisions. They calculate the CRC for each frame received prior to forwarding. Bandwidth is shared among all connected users. 9 What does switch latency describe? forwarding method used by a switch time it takes for a frame to be received by a switch improvement in network performance from using a switch time delay between when a frame enters and exits a switch increase in the size of a collision domain from using a switch 10 Which statements describe asymmetric switching? (Choose three.) It uses data compression algorithms to manage higher bandwidth interfaces. It is often used to provide high bandwidth uplinks for a number of lower bandwidth client interfaces. It provides connections between network segments that operate at different bandwidths. It uses cut-through forwarding when going from a lower bandwidth to a higher bandwidth interface. It is used to provide more bandwidth to network clients than to backbone or server links. It may require buffering frames before forwarding to the destination interface. 11 Which form of buffering is used by bridges? cut-through fragment-free fast-forward store-and-forward 12 How does an Ethernet bridge handle an incoming frame? (Choose three.) The source MAC address and input interface pair are added to the bridging table. The destination MAC address and input interface pair are added to the bridging table. If no match to the destination MAC address is found in the bridging table, the frame is discarded. If no match to the destination MAC address is found in the bridging table, the frame is flooded out all other interfaces. If a match to the destination MAC address is found in the bridging table, the frame is forwarded out the associated interface. If a match to the source MAC address is found in the bridging table, the frame is forwarded to all ports. 13 Refer to the graphic. Which point must be reached before a frame is forwarded when the switch is using store-and-forward mode? A B C D E F 14 Refer to the graphic. Which point in the frame must be reached before it is forwarded by a switch that is using fast-forward mode? A B C D E F 15 Which device provides segmentation within a single network? hub server switch transceiver 16 What are the functions of routers? (Choose three.) improving network performance by increasing latency by twenty to thirty percent segmenting broadcast domains forwarding packets based on destination network layer addresses segmenting collision domains forwarding packets as soon as the destination MAC address is read developing routing table entries based on source IP addresses 17 What are the functions of a Layer 2 Ethernet switch? (Choose three.) preventing broadcasts increasing available bandwidth per user decreasing the size of collision domains isolating traffic among segments routing traffic between different networks decreasing the number of broadcast domains 18 Hubs are concerned with which PDU? bits frames packets datagrams 19 Why would a network administrator segment a network with a Layer 2 switch? (Choose two.) to create fewer collision domains to enhance user bandwidth to create more broadcast domains to eliminate virtual circuits to isolate traffic between segments to isolate ARP request messages from the rest of the network 20 Which of the following is used to build a switching table? source IP addresses destination IP addresses destination MAC addresses source MAC addresses

评论