正文

Module 2 Exam - CCNA 22007-06-17 19:57:00

【评论】 【打印】 【字体: 】 本文链接:http://blog.pfan.cn/ccna/26863.html

分享到:

1
Which tasks can be accomplished by using the command history feature? (Choose two.)
View a list of commands entered in a previous session.
Recall up to 15 command lines by default.
Set the command history buffer size.
Recall previously entered commands.
Save command lines in a log file for future reference.

2
A network administrator needs to configure a router. Which of the following connection methods requires network functionality to be accessible?
console
AUX
Telnet
modem

3
Which connection method can be used to perform the initial configuration of a router?
use a serial connection of a computer connected to the console port of a router
telnet to the router through a serial port
use a vty port through the Ethernet interface
use a modem connected to the AUX port of the router

4
Which keystroke is used to move to the beginning of a command line?
Ctrl-A
Ctrl-B
Esc-A
Esc-B
Ctrl-C
Ctrl-Z

5
After the active IOS image has been loaded into RAM from flash memory, which commands could be used to display the file name of the active IOS? (Choose two.)
Router# show IOS
Router# show flash
Router# show nvram
Router# show version
Router# show startup-config
Router# show running-config

6
What information about the router and its startup process can be gathered from the output of the show version command? (Choose three.)
the last restart method
the command buffer contents
the amount of NVRAM and FLASH used
the configuration register settings
the location from where the IOS loaded

7
Under what conditions does the router enter setup mode? (Choose three.)
immediately after issuing the command Router#erase start
after issuing the command Router#setup
during the initial configuration of a router
after deleting the backup configuration and reloading the router
after deleting the running configuration

8
Which keystrokes can be used to return to the privileged mode from the interface configuration mode?
Ctrl-P
Ctrl-Shift-6, then X
Ctrl-Z
Esc

9
What baud rate needs to be configured on terminal emulation software to allow a connection to the console port of a router?
2400
4800
9600
14200
38400

10
Cisco IOS software is separated into two levels as a security feature. What are those two levels? (Choose two.)
global
privileged
local
user
interface

11
Which command takes precedence if the commands enable password and enable secret are both configured on a router?
enable password
enable secret
Neither. They are both enabled.
Neither. They cancel each other out.

12
When the router output is being viewed through a terminal program, which statements are true regarding the --More-- prompt at the bottom of the router display? (Choose two.)
Press the Spacebar to display the next line.
Press the Spacebar to view the next screen.
Press the PgDn key to view the next screen.
Press the Enter key to display the next line.
Press the Enter key to view the next screen.

13
What information does the name of the IOS file provide to the network administrator? (Choose three.)
the amount of NVRAM required to run the image
the hardware platform the image runs on
the various software platforms the image can run on
special features and capabilities of the image
the bandwidth supported by the IOS
where the image executes from and if it has been compressed

14
What is the default sequence for loading the configuration file?
NVRAM, FLASH, ROM
FLASH, TFTP,CONSOLE
NVRAM, TFTP, CONSOLE
FLASH, TFTP, ROM

15
Which tasks can be performed in the ROM monitor mode? (Choose two.)
recover from system failures
create startup configuration files
recover from lost passwords
configure IP addresses on all router interfaces
perform high level diagnostics
16
Which of the following statements concerning router interface modes are correct? (Choose three.)
User EXEC mode provides commands to monitor router operation.
Privileged EXEC mode only provides commands to change or configure router operation.
Password protected configuration modes can be accessed from either user EXEC or privileged EXEC modes.
On a router with the name Core1, the prompt indicating privileged EXEC mode is Core1#.
The command to enter privileged EXEC mode is Router# enable.
A username and password may be required to enter privileged EXEC mode.

17
Which of the following is the correct flow of routines for a router startup?
load bootstrap, load IOS, apply configuration
load bootstrap, apply configuration, load IOS
load IOS, load bootstrap, apply configuration, check hardware
check hardware, apply configuration, load bootstrap, load IOS

18


Which of the following identifies the correct items needed to initially configure a router?
1) DB-9-to-RJ-45 on the PC's serial port
2) a straight through cable
3) the router's console port
1) PC's Ethernet port
2) a crossover cable
3) the router's Ethernet port
1) DB-9-to-RJ-45 on the PC's serial port
2) a rollover cable
3) the router's Ethernet port
1) PC's Ethernet port
2) a rollover cable
3) the router's console port
1) DB-9-to-RJ-45 on the PC's serial port
2) a rollover cable
3) the router's console port
1) PC's Ethernet port
2) a rollover cable
3) the router's Ethernet port

19
What does the command sh? return as output if issued at the Router# prompt?
all show commands allowed in privileged mode
all commands beginning with the letters sh
an incomplete command error message
an invalid command error message

20
(1) Not At All Enthusiastic (2) Slightly Enthusiastic (3) Enthusiastic (4) Very Enthusiastic (5) Completely Enthusiastic
In your opinion (this has no bearing on your grade), please indicate how enthusiastic you are about the content of this course and the things you’re learning (or have learned):
21
(1) Not At All Motivated (2) Slightly Motivated (3) Motivated (4) Very Motivated (5) Completely Motivated
In your opinion (this has no bearing on your grade), please rate your motivation to do well in this course:
22
(1) Not At All Interested (2) Slightly Interested (3) Interested (4) Very Interested (5) Completely Interested
In your opinion (this has no bearing on your grade), please indicate your interest in this course:

阅读(6757) | 评论(11)


版权声明:编程爱好者网站为此博客服务提供商,如本文牵涉到版权问题,编程爱好者网站不承担相关责任,如有版权问题请直接与本文作者联系解决。谢谢!

评论

loading...
您需要登录后才能评论,请 登录 或者 注册