正文

Module 6 Exam - CCNA2007-05-15 19:51:00

【评论】 【打印】 【字体：大 中 小】 本文链接：http://blog.pfan.cn/ccna/25919.html

分享到：

Take Assessment - Module 6 Exam - CCNA 1 Networking Basics (Version 3.1)

 Time Remaining:

1
A router has an Ethernet, Token Ring, serial, and ISDN interface. Which interfaces will have a MAC address?
serial and ISDN interfaces
Ethernet and Token Ring interfaces
Ethernet and ISDN interfaces
Token Ring and serial interfaces

2


Refer to the exhibit. A technician wants to increase the available bandwidth for the workstation by allowing the switch and the NIC on the workstation to transmit and receive simultaneously. What will permit this?
CSMA/CD
full-duplex
FastEthernet
crossover cable

3
Which of the following are specified by IEEE standards as sublayers of the OSI data link layer? (Choose two.)
Logical Link Control
Logical Layer Control
Media Access Control
Logical Link Communication
Media Access Communication
Physical Access Communication

4
What are three functions of a NIC in a PC? (Choose three.)
A NIC connects the PC to the network media.
A NIC detects collisions on the Ethernet segment.
A NIC checks the formatting of data before it is transmitted.
A NIC passes the contents of selected frames to the upper OSI layers.
A NIC acknowledges and retransmits data that was not received properly.
A NIC discards frames when the destination IP address does not match the local host.

5
In an Ethernet LAN, how does the NIC know when it can transmit data?
An Ethernet NIC transmits data as soon as the frame is received.
An Ethernet NIC transmits data as soon as the NIC receives a token.
An Ethernet NIC transmits data when it senses a collision.
An Ethernet NIC transmits data after listening for the absence of a signal on the media.

6


Refer to the exhibit. Host A is communicating with host F. What happens to a frame sent from host A to host F as it travels over the Ethernet segments?
The frame format is modified as it passes through each switch.
The frame format remains the same across each Ethernet segment.
The frame format is modified as the media speed changed at switch B and switch E.
The frame format is modified as the media material changes between copper and fiber at switch C and switch D.

7
When a collision occurs in a network using CSMA/CD, how do hosts with data to transmit respond after the backoff period has expired?
The hosts return to a listen-before-transmit mode.
The hosts creating the collision have priority to send data.
The hosts creating the collision retransmit the last 16 frames.
The hosts extend their delay period to allow for rapid transmission.

8
Which statement describes how CSMA/CD on an Ethernet segment manages the retransmission of frames after a collision occurs?
The first device to detect the collision has the priority for retransmission.
The device with the lowest MAC address determines the retransmission priority.
The devices on the network segment hold an election for priority to retransmit data
The devices transmitting when the collision occurs DO NOT have priority for retransmission.

9
Why do hosts on an Ethernet segment that experience a collision use a random delay before attempting to transmit a frame?
A random delay is used to ensure a collision-free link.
A random delay value for each device is assigned by the manufacturer.
A standard delay value could not be agreed upon among networking device vendors.
A random delay helps prevent the stations from experiencing another collision during the transmission.

10


Refer to the exhibit. All hosts are in listen mode. Host 1 and Host 4 both transmit data at the same time. How do the hosts respond on the network? (Choose two.)
Hosts 1 and 4 may be operating full duplex so no collision will exist.
The hub will block the port connected to Host 4 to prevent a collision.
After the end of the jam signal, a backoff algorithm is invoked.
Hosts 1 and 4 are assigned shorter backoff values to provide them priority to access the media.
If a host has data to transmit after the backoff period of that host, the host checks to determine if the line is idle, before transmitting.

11
On a local area network, one workstation can send data on the line while it is receiving data. What type of data transfer does this describe?
hybrid
half duplex
full duplex
multilink

12
Which two devices can provide full-duplex Ethernet connections? (Choose two.)
hub
modem
repeater
NIC
Layer 2 switch

13
Where does the MAC address originate?
DHCP server database
configured by the administrator
burned into ROM on the NIC card
network configuration on the computer
included in the creation of the processor chip

14


Refer to the exhibit. The small office network shown in the exhibit consists of four computers connected through a hub. Which configuration would cause collisions and errors on the network?
autonegotiation
FastEthernet
peer-to-peer shared resources
administratively configured full duplex

15
In which two layers of the OSI model does Ethernet function? (Choose two.)
application
session
transport
network
data link
physical
16


Refer to the exhibit. The switch and workstation are administratively configured for full-duplex operation. Which statement accurately reflects the operation of this link?
No collisions will occur on this link.
Only one of the devices can transmit at a time.
The switch will have priority for transmitting data.
The devices will default back to half duplex if excessive collisions occur.

17
How many hexadecimal digits are in a MAC address?
2
8
12
16
32

18
At what layer of the OSI model does a MAC address reside?
1
2
3
4
7

19
Which characteristics describe carrier sense multiple access collision detect (CSMA/CD)? (Choose three.)
reliable
point-to-point
nondeterministic
connection-oriented
collision environment
first-come, first-served approach

阅读(2993) | 评论(0)


版权声明：编程爱好者网站为此博客服务提供商，如本文牵涉到版权问题，编程爱好者网站不承担相关责任，如有版权问题请直接与本文作者联系解决。谢谢！

评论

暂无评论
您需要登录后才能评论，请 登录 或者 注册